Cisco 640-722 Exam - Cheat-Test.com
Free 640-722 Sample Questions:
The IEEE 802.11n standard provides 40-MHz channels, improved MAC efficiency, and MIMO.
Which three elements define the 802.11n implementation of MIMO? (Choose three.)
A. channel bonding
B. dynamic frequency selection
C. maximal ratio combining
D. packet aggregation
E. spatial multiplexing
F. transmit beam forming
Which two statements about WiMAX technology are true? (Choose two.)
A. WiMAX is defined by 802.11i.
B. Typically, fixed WiMAX networks have a higher-gain directional antenna installed near the
C. WiMAX is capable of working as a long-range system over several miles.
D. WiMAX works only for licensed frequencies.
Which governing body analyzes the applications and environments in which wireless networks are
E. WiFi Alliance
Which description best describes upfade in a multipath environment?
A. In this situation, multiple signal paths are not sent at exactly the same time. The receiver
receives a positive crest on the primary signal and a negative crest on the secondary signal.
B. In this situation, the multiple signal paths are distorted and difficult to understand.
C. In this situation, the multiple signal paths are weaker than they should be because the signals
are out of phase with each other.
D. In this situation, the signal is stronger than it should be because multiple signal paths are
received twice at exactly the same time, which results in the multiple signals being in-phase.
A controller is connected to a Cisco Catalyst switch. The switch port configuration looks like this:
interface GigabitEthernet 1/0/10
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,20,30,50
switchport trunk native vlan 20
switchport mode trunk
Which controller CLI command assigns its management interface to the native VLAN interface of
the Cisco Catalyst switch?
A. config interface vlan management 0
B. config interface vlan management 1
C. config interface vlan management 20
D. config interface vlan management 30
E. config interface vlan management 50
Which statement about an infrastructure basic service set is true according to IEEE 802.11
A. The set also is called an ad hoc network.
B. The BSSID is generated from the first wireless client that starts up in the IBSS.
C. The set enables the use of ESS.
D. No signals are relayed from one client to another client.
Which two factors must be considered when evaluating an RF interferer for severity? (Choose
A. distance from the AP
C. the type of security crack being used
D. duty cycle
E. number of interfering IP stations in the cell
F. duplicate SSID
What is the difference between the IEEE, the WiFi Alliance, and the FCC, ETSI, and TELEC?
A. The IEEE and FCC are responsible for the standards that apply to wireless networks. The WiFi
Alliance, ETSI, and TELEC are the governmental agencies that regulate compliance with local
B. The IEEE is responsible for Layer 1 and Layer 2 protocols. The WiFi Alliance is responsible for
interoperability testing. The FCC, ETSI, and TELEC are responsible for radio frequency and
transmission power-level regulations and standards in the U.S., Europe, and Japan.
C. The IEEE is responsible for Layer 1 and Layer 2 protocols. The FCC, ETSI, and TELEC are
responsible for interoperability testing and compliance. The WiFi Alliance is responsible for radio
frequency and transmission power-level regulations and standards on a global basis.
D. The IEEE and FCC are responsible for the Layer 3 protocol support and frequency and powerlevel
regulations in the United States. ETSI and TELEC are responsible for frequency and powerlevel
regulations in Europe and Japan. The WiFi Alliance is responsible to interoperability testing.
What is an MBSSID?
A. a virtual AP configured on a physical AP that share a single physical device, which is one halfduplex
B. a set of physical APs configured in a BSA to form cells that are controlled by a single controller
C. the group of clients that are allowed to gain access to one or more SSIDs configured in an AP
D. the identified overlap area between two cells, which identifies the clients that are operating in
that area at any given time
What is the equivalent of 26 dBm in milliwatts?
A. 4 mW
B. 40 mW
C. 100 mW
D. 400 mW
E. 1000 mW